Home Decor

How to Make DIY Table Legs to Upgrade Any Side Table

Table legs aren’t simply utilitarian components. All around created legs can make the vibe of the table. Wood table legs are basic and modest to make from dimensional timber found at your neighborhood home focus.

Making Wood Table Legs

To accomplish the presence of a thick, strong table leg, two sheets are covered with stick and intertwined with bar braces. The clips are left on for various hours: pressing factor and time equivalent strength.

When the braces are delivered, every leg is torn (or run the long way) through a table saw to carry the leg to a uniform 3-inch by 3-inch size. An electric wood planer smooths down the sides. In the event that you don’t have a planer, you can substitute with a sander.

Subsequent to slicing the legs to length, utilize a switch to adjust the sharp corners. Sand one final time with fine-coarseness paper, then, at that point paint or stain and connect to the tabletop.

Type of Wood to Use

Two-by-fours range in price and quality from softwoods like whitewood, yellow pine, or cedar to hardwoods such as red oak, cherry, mahogany, or maple.

Softwoods usually cost about $1 to $2 per linear foot. Mahogany, one of the most expensive two-by-fours you can buy, costs $15 to $25 per linear foot.

Choose clear wood. Avoid wood with knots, cracks, or imperfections. Do not use pressure-treated wood.

Alternative Materials for Making Table Legs

  • Steel Pipe: Steel pipe is a popular table leg alternative to wood that fits well with an industrial style. Choose your desired length of pipe, then turn the pipes clockwise by hand into floor flanges. Screw the flanges onto the bottom of the tabletop.
  • Metal Hairpin Legs: Originally designed for mid-century modern coffee table legs, metal hairpin legs can now be found in longer sizes for larger tables.
  • Parsons Table Legs: Parsons legs are about as easy as table legs can get. These two-by-two wood legs come with a pre-attached bolt at one end. Simply screw four metal mounting plates on the bottom of the table, then turn the legs into the plates by hand.

Safety Considerations

Observe all safety instructions that come with your table saw. To avoid kickback, be sure that the blade and the gate are parallel with each other. Make sure that the table saw’s riving knife is installed. Standard with most modern table saws, the riving knife helps to prevent kickback, too.

What You’ll Need

Equipment / Tools

  • Table saw
  • Electric miter saw
  • Electric planer
  • Orbital sander
  • 4 bar clamps
  • Wood glue
  • Rags
  • Tack cloth

Materials

  • 4 two-by-fours, each 8-foot
  • Scrap two-by-fours

Instructions

  • Cut Wood
  • Glue Wood Pieces
  • Clamp Pieces
  • Rip Table Legs
  • Plane Table Legs
  • Cut Ends of Table Legs
  • Use Router on Table Legs
  • Sand Table Legs
  • Paint or Stain Table Legs
  1. Cut Wood

    With an electric miter saw or by hand, cut each of the four two-by-fours in half to produce eight table legs, each 4 feet long. The legs will later be cut down to the correct size.


  2. Glue Wood Pieces

    Apply glue liberally to one piece of wood. Lay another piece of wood on top of this. Repeat for the other three pairs of wood.


  3. Clamp Pieces

    Clamp the four table legs with the bar clamps. Use a piece of scrap wood on each side to avoid denting the table legs with the bar clamps. Tighten the clamps. Glue will likely ooze out from the sides. Wipe up the glue with the rag.

    Warning

    Check the surfaces of the table legs for stray glue before clamping the wood together. This will help you avoid gluing the legs together.


  4. Rip Table Legs

    After about four hours, release the bar clamps. Run each leg through the table saw to rip it to 3 inches square. Cut each of the four sides of each leg by 1/4 inch.


  5. Plane Table Legs

    If you have an electric wood planer, run all four sides of each table leg through the planer to smooth it down.

    Alternatively, use a belt sander to smooth down the surfaces.


  6. Cut Ends of Table Legs

    Most dining tables range from 28 to 30 inches in height. Use the electric miter saw to cut each table leg down to this length, or to your desired length.


  7. Use Router on Table Legs

    Fit a roundover bit on the router. Use the router on all four edges of each table leg to smooth them down. Also, run the roundover bit along the feet of the table legs to prevent the wood from splintering when the table is moved on the floor.


  8. Sand Table Legs

    Fit the oscillating sander with fine-grit sandpaper such as #220. Sand all four sides of each table leg. If using hardwood, you can increase the grit to #320 for an even smoother finish.


  9. Paint or Stain Table Legs

    Clean off the table legs with a tack cloth. If painting the legs, first apply primer. If staining the legs, apply a stain pre-conditioner for even, balanced staining. Apply a clear top coating after the stain has dried.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close